Plumbing for Beginners: The Essentials for Bathtub Installation
Plumbing for Beginners: The Essentials for Bathtub Installation
Blog Article
How do you really feel about How to Install a Bathtub?
Mounting a tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is also a reasonably hard task. If the old tub is conveniently accessible, the job can move easily; if you need to open a wall surface to remove the old bathtub and place the new tub, the job is a lot harder. In either case, the task is within a house handyman's abilities, although you will certainly require a helper to leave the old tub as well as set in the new one. Ensure you have qualified on your own for the work as well as are comfortable attempting it. As opposed to working with a service provider to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Possibilities are you may require a professional plumber to make tube connections.
This post will aid you install a brand-new bathtub in your washroom if you have currently purchased a new tub and do not need to transform the arrangement of your previous water supply pipelines.
Your tools as well as material checklist must consist of the following:
Getting ready for the Installation
First of all, the supporting structure supplied with the bathroom should be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is also practical to fit a supporting plate under the faucets unit to avoid pressure on the bath tub.
Fit the flexible tap ports to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited gain access to that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the remaining water that will certainly originate from the pipelines. Once the supply pipes have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from transforming throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Prior to proceeding to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Utilizing the two wooden boards under its feet, place the bathtub in the called for position. The wooden boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny points.
The following objective is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and also changing the feet on the bath tub till the level reads level.
To mount taps, fit the bottom of the furthest flexible tap connector to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the supply of water and examine all joints and brand-new pipework for leakages and tighten them if required. Load the tub as well as also check the overflow outlet and the typical outlet for leaks.
Ultimately, take care of the bath paneling as explained in the supplier's instruction manual. Tiling and also securing around the bathtub should wait up until the tub has actually been utilized at the very least once as this will resolve it into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washers remain in location in between the tap and also the sink. Secure the faucet in place with the producer given backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous kind should be linked to the tap ends initially, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to break a rigid seal, creating the water to pass through the wall between the bathroom and the tiling, leading to difficulties with moisture and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can split fairly very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly available on the market. It is suggested to fit the floor tiles making use of water-resistant or water resistant sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that article on Installing A Bathtub through a friend on our other web blog. Do you know about anybody else who is fascinated with How to Install a Bathtub? Do not hesitate to promote it. We cherish reading our article about Installing A Bathtub.
Ready to help! Report this page